Made of composite material. Suitable for the preparation of 10 cm test cubes. Composed of a base plate, four side walls, an upper square ring joining the walls and two rubber rings.
Weight: 0,9 kg.
Made of composite material. Suitable for the preparation of 15 cm test cubes. Composed of a base plate, four side walls, an upper square ring joining the walls and two rubber rings.
Weight: 1,5 kg.
Made of composite material. Suitable for the preparation of 20 cm test cubes. Composed of a base plate, four side walls, an upper square ring joining the walls and two rubber rings.
Weight: 3,5 kg.
Made of composite material. Suitable for the preparation of cylinders 15x30 cm (dia. x height). Composed of a base plate, two semicircular walls, an intermediate ring and an upper ring.
Weight: 2,4 kg.
With meter, designed to carry out the workability test according to Abrams's method. This version is made of metal with stainless steel slump cone and hopper in composite material. It is supplied complete with baseplate in galvanised sheet iron, tamping rod and slump meter.
Dimensions: 520x470x330mm
Weight: 8 kg
This vibrating table is called unidirectional because a pair of motorvibrators located al a suitable distance of each other provide a regular unidirectional shaking movement lo the aggregates contained in the mix, which is the only method lo maintain the initial characteristics of compactness and homogeneity of the specimen. The high rigidity of the working surface guarantees the even distribution of the vibrations on the latter, so that the result of the compaction is independent from its position. The clamping system of the moulds on the vibrating surface is highly practical and safe. Some locking devices sliding along the slots make il possible lo fix either a fourgang mould or various twogang moulds or single moulds. The apparatus can hold a maximum of one 20 cm fourgang cube mould.
Vibrating Force: 120/260 kg.
Vibration Frequency: 3000 cicli/min.
Power Supply: 220-240 V 50 Hz +T
Absorbed Power: 0,5 kW
Dimensions: 1170x550x500mm
Weight: 108 kg.
With electric motor. This tool is very simple and practical for on site vibration of concrete in moulds. The motor is of the double isolation type, in compliance with International Standards.
Diameter of standard hammer: 22mm
Cable lenght: 1,5m
Power supply: 220-240 V 50 Hz +T
Dimensions: 220x70x630mm
Weight: 3 kg.
Used for the determination of the air content in concrete. This instrument directly supplies the rate of air contained in the form of bubbles in a pasty mass. The mix is subjected to a pressure that is twice that of the atmosphere, so that the volume of concrete which is uncompressible remains unchanged, while the volume of air is reduced to the half. The instrument is made from light alloy and it is supplied calibrated, complete with tamping rod and hand pump.
Volume: 5 l
Pressure: 2 bar
Dimensions: 340x630mm (Diameter x Height)
Weight: 11 kg.
It is suitable for installation of materials testing machines in compression with pressures up to 700 bar.
The machine is suitable to effectuate compression tests on:
• Cylindrical test pieces with diameter of 150 mm and height of 300 mm
• Cylindrical test pieces with diameter of 160 mm and height of 320 mm
The machine is suitable to effectuate compression tests on:
• Cylindrical test pieces with diameter of 150 mm and height of 300 mm
• Cylindrical test pieces with diameter of 160 mm and height of 320 mm
The machine is suitable to effectuate compression tests on:
• Cylindrical test pieces with diameter of 150 mm and height of 300 mm
• Cylindrical test pieces with diameter of 160 mm and height of 320 mm
• Cubic test pieces with side of 150 and 200 mm
The machine is best suited for test compression at:
• Cylindrical samples diameter 150mm height 300mm
• Cylindrical samples diameter 160mm height 320mm.
